Board Cameras

CCD BOARD CAMERAS

B/W CCD Board lens
CNL-100

B/W CCD Pinhole Camera
CNP-101

CCD Color Pinhole
CNP-201-C

CCD Color Lens
CNL-200-C

B/W CCD BOARD CAMERASFeatures:

CCD Board Camera Black and white
1/3" CCD; 430 TV Lines Resolution
0.08 Lux
3.6mm / F2.0, 90 degree field of view
12 VDC @ 90 - 100mA
Connector with Pre-tinned lead
7.5 - 13 VDC operation
Array size 542 X 492
270,000 Pixels
Auto-Shutter 1/60 to 1/100,000 Second
Infrared sensitive
PAL also available

Instructions:

The CCD B/W cameras have optimal performance at 12VDC. Do not exceed 13 VDC under any circumstances. When wiring the cameras, it is strongly recommended that the power is turned off.

Many 12 Volt adapters have an extremely high open circuit voltage which means that an excessive voltage spike can damage the cameras. If you are uncertain about your power source, order the XF-200L. It provides 12 volts under load for this camera module.

The CNL-100 lens can be adjusted by rotating lens in either direction for proper focus. The spring adjustment makes the job easier by providing tension to lock the lens in place. Some designs employ an easily removable set-screw.

Pin hole lens design, CNP-101, can be adjusted if required by using the small Allen-head wrench and adjusting the set-screw located on the ridge, just below the lens. Do not over-tighten! In some instances, a set-screw is not employed. In this case, just rotate the lens to focus properly.

COLOR CCD BOARD CAMERAS
Features:

CCD Board Camera Color
1/4" CCD; 350 TV Lines Resolution
2.0 Lux
3.6mm / F2.0, 90 degree field of view
12 VDC @ 110mA
Connector with Pre-tinned lead
10-13 VDC operation
One board design
Sony chip set
Auto-Shutter 1/60 to 1/100,000 Second
Infrared sensitive
PAL also available

Instructions:

The CCD color cameras have optimal performance at 12VDC. Do not exceed 13 VDC under any circumstances. When wiring the cameras, it is strongly recommended that the power is turned off.

Many 12 Volt adapters have an extremely high open circuit voltage which means that an excessive voltage spike can damage the cameras. We recommend the use of a 12 volt regulated, XF-201-R (regulated) power supply for this module.

The CNL-100-C lens can be adjusted by rotating lens in either direction for proper focus. The spring adjustment makes the job easier by providing tension to lock the lens in place. Some designs employ an easily removable set-screw.

Pinhole lens design, CNP-101-C, can be adjusted if required by using the small Allen-head wrench and adjusting the set-screw located on the ridge, just below the lens. Do not over-tighten! In some instances, a set-screw is not employed. In this case, just rotate the pinhole lens to focus properly.
Note: -C for color version

CMOS BOARD CAMERAS

B/W CMOS Board lens
CML-100

B/W CMOS Pinhole Camera
CMP-101

Color CMOS Board Lens
CML-100-C

Color CMOS Pinhole
CMP-101-C

B/W COMES BOARD CAMERASFeatures:

Size: 15 x 22mm
Pixels: 365K(PAL), 250K(NTSC)
Resolution: horizontal 380TV lines
Auto electronic exposure: 1/60 - 1/15000sec
Automatic exposure/gain/white balance
Min. illumination:<3 Lux at @f1.2
S/N ratio: 48dB
Lens: f=3.6mm/F:2.0/92o, (Pinhole f=5.5mm)
Power supply: 5 - 7V
Power consumption: 40mA(max)

COLOR CMOS BOARD CAMERASFeatures:

Size: 15 x 22mm
Pixels: 365K(PAL), 250K(NTSC)
Resolution: horizontal 320TV lines
Auto electronic exposure: 1/60 - 1/15000sec
Automatic exposure/gain/white balance
Min. illumination:<3 Lux at @f1.2
S/N ratio: 48dB
Lens: f=3.6mm/F:2.0/92o, (Pinhole f=5.5mm)
Power supply: 5 - 7V
Power consumption: 40mA(max)